P retty card to say hello using Stampin' Up! products.
Project Recipe
Cut cardstock, designer paper, and Adhesive Sheets pieces to the following sizes using a Paper Trimmer:
- card from Moody Mauve Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 4" x 5-1/4" from Basic White Cardstock
- 3-1/4" x 4" of large pink and white daisies with yellow brown leaves on purple background design from Fresh As A Daisy 12" x 12" Designer Series Paper, cut so the daisies are right side up on the vertical rectangle
- 1-3/4" x 3-3/4" from Bubble Bath Cardstock
- 1-3/4" x 3-3/4" from Moody Mauve Cardstock
- 1-5/8" x 3-5/8" from Adhesive Sheets
- 1-1/2" x 2" from Basic White Cardstock
- 3/4" x 3" from Bubble Bath Cardstock
Adhere the piece of Fresh As A Daisy Designer Paper to the bottom of the large, vertical white rectangle so the left, right, and bottom edges are even.
Cut a 4-3/4" piece of the Moody Mauve jute from the 2023-2025 In Color Jute Trim.
Lay the jute trim across the layered cardstock/designer paper rectangle so it covers the seam between the pieces. Fold the ends of the jute trim over and secure the jute trim in place on the back with strips of Tear & Tape Adhesive.
Remove the protective backings from the Tear & Tape pieces and add Stampin' Seal to the back of the Basic White rectangle. Adhere the rectangle to the front of the Moody Mauve card.
Pick out the more solid "sending" word die from the Sending Dies. Put it on top of the 1-3/4" x 3-3/4" Bubble Bath rectangle on a platform on your Stampin' Cut & Emboss Machine. Run through the machine.
Peel the protective backing off of the Adhesive Sheets rectangle. Adhere the Adhesive Sheets rectangle to one side of the Moody Mauve rectangle. Be sure to leave the other protective backing in place for now.
Pick out the more detailed "sending" word die from the Sending Dies. Put it on top of the Moody Mauve rectangle on a platform on your Stampin' Cut & Emboss Machine so the Moody Mauve (purple) side is face up. Run through the machine. Use the paper-piercing tool on the Take Your Pick to remove the pieces.
Carefully remove the protective backing from the detailed "sending" word cut out. Adhere it to the center of the more solid "sending" word cut out.
Use Multipurpose Liquid Glue or Fine-Tip Glue Pen to adhere the layered "sending" word cut out to the front of the card at a slight angle as shown at the top of the card..
As you are ready to stamp using the Sending Smiles Set, place the cardstock on the Stampin' Pierce Mat. Using the mat will help you get a cleaner image each time you stamp.
Mount one of the shorter sentiments of choice from the Sending Smiles Set on Block G. Ink it up with the Moody Mauve Ink Pad. Stamp it in the center of the skinny Bubble Bath strip.
Pick out the shorter, skinny label die from the Sending Dies. Put it on top of the stamped sentiment on a platform on your Stampin' Cut & Emboss Machine so the sentiment is centered top to bottom in the die and is closer to the right edge. Run through the machine.
Use Mini Stampin' Dimensionals to adhere the sentiment strip cut out to the front of the card as shown so it overlaps the bottom of the "g" at the end of the "sending" word a bit and is about 1/2" from the right side of the card.
Mount the larger, flatter flower image from the Sending Smiles Set on Block B. Ink it up with the Bubble Bath Ink Pad. BEFORE STAMPING, add some Moody Mauve to the edges of the stamp using a Small Blending Brush rubbed across the open Moody Mauve Ink Pad to get it inky. Breathe on the stamp to moisten the ink. Stamp it on the small white rectangle.
Mount the simple oval flower center image from the Sending Smiles Set on Block A. Ink it up with the Moody Mauve Ink Pad. Stamp it in the center of the stamped flower image.
Pick out the matching flower die from the Sending Dies. Put it on top of the stamped image on a platform on your Stampin' Cut & Emboss Machine so it is centered over the image. Run through the machine.
If desired, use the Small Blending Brush with Moody Mauve Ink on it to color the edges of the flower cut out.
Use Stampin' Dimensionals to adhere the flower cut out to the front of the card as shown so it overlaps the bottom of the "s" in the "sending" word, the top of the designer paper, and the left edge of the sentiment strip cut out.
Use the mini spatula on the Take Your Pick to carefully peel up 1 small jewel from the sheet of Iridescent Rhinestone Basic Jewels making sure that you get the adhesive backing as well. Adhere it to the top of the "sending" cut out as the dot on the "i."
Use the mini spatula on the Take Your Pick to carefully peel up 1 medium jewel from the sheet of Iridescent Rhinestone Basic Jewels making sure that you get the adhesive backing as well. Adhere it to one side of the center of the stamped daisy as shown.
Cut a 6" piece of the Moody Mauve jute from the 2023-2025 In Color Jute Trim.
Fold the jute trim in half. Slide one end of the folded trim under the trim already on the card front on the right side. Tie in place with an knot just below the right end of the sentiment strip cut out as shown. Trim the ends.