P retty card for a crafter using Stampin' Up! products.
Project Recipe
Cut cardstock and designer paper pieces to the following sizes using a Paper Trimmer:
- card from Moody Mauve Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 4" x 5-1/4" from Fresh Freesia Cardstock
- 3-7/8" x 5-1/8" of lines of pink and white
design from Delightfully Eclectic 12" x 12" Designer Series Paper, cut so the lines are horizontal on the vertitcal rectangle
- 2" x 2-1/2" from Basic White Cardstock
- 2-1/4" square from Basic White Cardstock
Use the Paper Trimmer to cut the vertical Delightfully Eclectic Designer Paper rectangle at the 1-3/4" mark all the way down.
Flip the thinner rectangle of designer paper over so the floral side is showing. Adhere it to the left side of the vertical Fresh Freesia rectangle so about 1/16" of Fresh Freesia shows on the top, left, and bottom edges.
Adhere the larger strip of designer paper to the right side of the Fresh Freesia rectangle so the stripes are showing and about 1/16" of Fresh Freesia shows on the top, right, and bottom edges. You may need to overlap the right edge of the floral strip of designer paper a tiny bit.
Cut a 5-3/4" piece of the Petal Pink ribbon from the Ribbon Duo Combo Pack.
Lay the ribbon across the cardstock/designer paper rectangle so it covers the seam between the two pieces of designer paper . Fold the ends of the ribbon over and secure the ribbon in place on the back with strips of Tear & Tape Adhesive.
Remove the protective backings from the Tear & Tape pieces and add Stampin' Seal to the back of the Fresh Freesia rectangle. Adhere the rectangle to the front of the Moody Mauve card.
As you are ready to stamp using the Crafting With You Set, place the cardstock on the Stampin' Pierce Mat. Using the mat will help you get a cleaner image each time you stamp.
Mount the grouping of flowers and leaves image from the Crafting With You Set on Block B. Ink it up with the Bubble Bath Ink Pad. Stamp the image near the upper right corner of the white square, leaving room to cut it out.
Mount the "you inspire me" or " with love" sentiment from the Crafting With You Set on Block B. Ink it up with the Garden Green Ink Pad. Stamp it on the previously stamped white square so it is centered side to side on the stamped floral image and slightly closer to the top. Be sure to leave room to cut it out.
Pick out the square die from the Stylish Shapes Dies that cuts out a 1-15/16" square. Put it on top of the stamped white square on a platform on your Stampin' Cut & Emboss Machine so the stamped images are as close as possible to the upper right corner. Run through the machine.
Adhere the sentiment square to the front of the card as shown so it overlaps the ribbon and left side of the floral designer paper strip and is about 1-1/4" from the top and 1" from the right side of the card.
Mount the Stampin' Cut & Emboss Machine image from the Crafting With You Set on Block D. Ink it up with the Moody Mauve Ink Pad. Stamp it on the remaining white rectangle.
Pick out the matching, open Cut & Emboss Machine die from the Crafting With You Dies. Put it on top of the stamped image on a platform on your Stampin' Cut & Emboss Machine so it is centered over the image. Run through the machine.
Use Stampin' Dimensionals to adhere the machine cut out to the front of the card as shown so it overlaps the lower left corner of the sentiment square.
Use the mini spatula on the Take Your Pick to carefully peel up three sizes of Moody Mauve dots from the sheet of 2023-2025 In Color Dots making sure that you get the adhesive backings as well. Adhere them to the card front as shown.