B reast cancer thinking of you card using Stampin' Up! products.
Project Recipe
Cut cardstock and designer paper pieces to the following sizes using a Paper Trimmer:
- card from Bubble Bath Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 4" x 5-1/4" from Fresh Freesia Cardstock
- 3-7/8" x 5-1/8" of pink triangles on white background design from Delightfully Eclectic 12" x 12" Designer Series Paper
- 2-1/2" x 4" from Fresh Freesia Cardstock
- 2-1/2" x 4" from Bubble Bath Cardstock
- 1-1/2" x 1-3/4" from Basic White Cardstock
- small scrap of Fresh Freesia Cardstock
Adhere the piece of Delightfully Eclectic Designer Paper to the center of the large Fresh Freesia rectangle and then to the front of the Bubble Bath card.
Mount the Countryside Corners stamp on Block F. Leave the stamp rubber side up on your work surface and press the open Fresh Freesia Ink Pad to the center of the stamp a couple of times to get it inky.
Leave the stamp inky rubber side up on your work surface. Carefully place the smaller Fresh Freesia rectangle on top of the inky stamp so it covers the center of the stamp and all of the third smallest (floral dots) frame. Place a piece of Grid Paper on top of the cardstock/inky rubber and rub firmly all over. Remove the Grid Paper and the inked up cardstock rectangle. Set aside. Clean the stamp using the Stampin' Scrub and Stampin' Mist Stamp Cleaner and/or Simply Shammy, but leave the stamp on the block.
Re-ink the Countryside Corners stamp on Block F by pressing the open Bubble Bath Ink Pad to the center of the stamp a couple of times again to get it inky.
Leave the stamp inky rubber side up on your work surface. Carefully place the Bubble Bath rectangle on top of the inky stamp so it covers the center of the stamp and all of the smallest frames. Place a piece of Grid Paper on top of the cardstock/inky rubber and rub firmly all over. Remove the Grid Paper and the inked up cardstock rectangle. Set aside.
Tip: I just clean my large background stamps by running water over them until the water runs clear and then letting them air dry.
Pick out the die from the Countryside Corners Dies that cuts out a label that is 1-7/8" x 3-1/2". Put it on top of the stamped label image on the Fresh Freesia cardstock on a platform on your Stampin' Cut & Emboss Machine so it is centered over the image. Run through the machine.
Pick out the die from the Countryside Corners Dies that cuts out a label that is 1-5/16" x 2-7/8". Put it on top of the stamped label image on the Bubble Bath cardstock on a platform on your Stampin' Cut & Emboss Machine so it is centered over the image. Run through the machine.
Adhere the Bubble Bath label cut out to the center of the Fresh Freesia label cut out.
Adhere the layered label cut outs vertically to the front of the vertical card in the center.
As you are ready to stamp using the Charming Sentiments Set, place the cardstock on the Stampin' Pierce Mat. Using the mat will help you get a cleaner image each time you stamp.
Mount the "faith over fear" sentiment from the Charming Sentiments Set on Block B. Ink it up with the Fresh Freesia Ink Pad. Stamp it in the center of the small white rectangle.
Pick out the matching die from the Sentiment Silhouettes Dies. Put it on top of the stamped sentiment on a platform on your Stampin' Cut & Emboss Machine so the sentiment is centered in the die. Run through the machine.
Use Mini Stampin' Dimensionals to adhere the sentiment cut out to the front of the card so it is centered over the layered label cut outs.
Cut a 6" piece of the Bubble Bath ribbon from the 3/8" Sheer Ribbon Combo Pack.
Fold the ribbon in half to make a cancer ribbon. Use a Mini Glue Dot where the ribbon overlaps to hold it together.
Use another Mini Glue Dot where the ribbon crosses over to adhere the ribbon to the front of the card at a slight angle so it overlaps the bottom right side of the layered label cut outs as shown. Use Paper Snips Scissors to trim the ends of the ribbon to sharp angles.
Pick out the the small, solid, smooth heart die from the Sentiment Silhouettes Dies. Put it on top of the tiny piece of Fresh Freesia cardstock on a platform on your Stampin' Cut & Emboss Machine. Run through the machine. Use the paper-piercing tool on the Take Your Pick to remove the pieces.
Use a Mini Glue Dot to adhere the small heart cut out to the front of the card so it is centered over the ribbon where it crosses.
Use the mini spatula on the Take Your Pick to carefully peel up a large jewel from the sheet of Iridescent Rhinestone Basic Jewels making sure that you get the adhesive backing as well. Adhere it to the center of the small heart on the ribbon.