P retty thinking of you card made with Stampin' Up! products.
Project Recipe
Cut cardstock and designer paper pieces to the following sizes using a Paper Trimmer:
- card from Gorgeous Grape Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 4" x 5-1/4" from Shaded Spruce Cardstock
- 3-7/8" x 5-1/8" of large, watercolor purple flowers and green stems and leaves design from Perennial Lavender Designer Series Paper, cut so the stems are vertical on the vertical rectangle
- 3" x 4-1/4" from Basic White Cardstock
- 1-1/2" x 2-1/2" from Gorgeous Grape Cardstock
Adhere the piece of Perennial Lavender Designer Paper to the center of the large Shaded Spruce rectangle and then to the front of the Gorgeous Grape card.
Mount the large, half flower image from the Translucent Florals Set on Block C. Ink it up with the Gorgeous Grape Ink Pad. Stamp it in the center of the vertical white rectangle close to the top edge.
Mount the thin stem image from the Translucent Florals Set on Block C. Ink it up with the Shaded Spruce Ink Pad. Stamp it on the white rectangle so it comes down from the bottom of the center of the previously stamped flower image.
Mount the double leaves image from the Translucent Florals Set on Block B. Ink it up with the Shaded Spruce Ink Pad. Stamp it on the white rectangle so it comes off from the left side of the stem with the smaller leaf on the bottom and the top leaf about 1/4" from the bottom of the flower.
Mount the single leaf image from the Translucent Florals Set on Block B. Ink it up with the Shaded Spruce Ink Pad. Stamp it on the white rectangle so it comes off from the right side of the stem opposite the other leaves.
If needed, use the fine tip of the Shaded Spruce Stampin' Write Marker to draw in thin lines connecting the leaves to the stem.
Pick out the deckled rectangle die from the Deckled Rectangles Dies that cuts out a 2-5/8" x 4" deckled rectangle. Put it on top of the stamped flower, stem, and leaves image on a platform on your Stampin' Cut & Emboss Machine so it is centered over the image. Run through the machine.
Adhere the floral rectangle cut out to the front of the card as shown so it is centered side to side and is about 5/8" from the top edge.
Pick out the large, interconnected words die from the Thoughtful Moments Hybrid products. Put it inside the Embossing Folder from the Thoughtful Moments Hybrid products so it fits into the grooves around the corresponding words cut into the inside of the top flap (the one with the line and logo printed on it) of the Embossing Folder. Place the Gorgeous Grape rectangle into the layered dies/embossing folder so it is centered over the "thinking of you" sentiment area. Close the folder and put it on a platform on your Stampin' Cut & Emboss Machine. Run through the machine. This will cut out and emboss the words at the same time.
Use Stampin' Dimensionals to adhere the words cut out to the front of the card as shown so it is centered on the floral rectangle cut out at the bottom and covers the bottom of the stem.
Cut a 4" piece of the Shaded Spruce 1/2" Satin & Sheer Ribbon.
Tie a half knot in the center of the ribbon. Trim the ends.
Use a Mini Glue Dot to adhere the ribbon knot to the front of the card at a slight angle as shown so it covers the bottom left corner of the floral rectangle cut out.
Use the mini spatula on the Take Your Pick to carefully peel up one large, one medium, and one small Gorgeous Grape dots from a sheet of Glossy Dots Assortment making sure that you get the adhesive backings as well. Adhere them to the card front as shown making sure the large cot covers the bottom of the flower at the stem.