V intage style card perfect for a thank you or congratulations using Stampin' Up! products.
Project Recipe
Cut cardstock and designer paper pieces to the following sizes using a cutting and scoring tool and Paper Snips:
- card from Sahara Sand Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 4" x 5-1/4" from Petal Pink Cardstock
- 2" x 4" from Sahara Sand Cardstock
- 2-1/2" square from Petal Pink Cardstock
- large Terracotta medallion roughly cut out with Paper Snips from terracotta medallions on light tan background design from Woven Threads Designer Series Paper
Open the Tin Tile 3D Embossing Folder in front of you. Lightly rub the open Terracotta Tile Ink Pad over the inside of the front flap (the one that has the "Stampin' Up!" logo on it). You are just trying to get a little ink on the raised areas.
Insert the large Petal Pink rectangle into the inked up Tin Tile 3D Embossing Folder. Use the line drawn on the front flap of the folder to help you line the cardstock up straight. Run the folder with the cardstock inside through your die cutting and embossing tool.
Tip: Clean the embossing folder by running it under water until no more ink is coming off. Air dry.
Adhere the dry embossed, inked up Petal Pink rectangle to the front of the Sahara Sand card.
Unlock the Delightful Tag Topper Punch. Slide one short end of the Sahara Sand strip into the punch as far as it will go and punch.
As you are ready to stamp using the Royal Peacock Photopolymer Set, place the cardstock on the Stampin' Pierce Mat. Using the mat will help you get a cleaner image each time you stamp.
Mount the "You Are Incredible" sentiment from the Royal Peacock Set on Block G. Ink up the stamp with the Terracotta Tile Ink Pad. Stamp the sentiment on the bottom of the tag in the center about 1//4" from the bottom.
Pick out the smooth circle die from the Layering Circles Dies that cuts out a smooth circle that is 1-7/8" wide. Put it on top of the roughly cut out medallion from the Woven Threads Designer Series Paper on a platform on your cutting and embossing tool so the medallion is centered. Run through the tool.
Pick out the scalloped circle die from the Layering Circle Dies that cuts out a scalloped circle that is 2-1/4" wide. Put it on top of the Petal Pink square on a platform on your cutting and embossing tool. Run through the tool.
Adhere the medallion circle to the center of the Petal Pink scalloped circle.
Adhere the matted circles to the tag just above the stamped sentiment.
Cut a 2-1/4" piece of Sahara Sand 5/8" Woven Threads Trim. Pull the string from the bottom edge to make the trim turn into tassels (if it isn’t already pulled free).
Put a strip of Tear & Tape on the bottom of the tag so it covers about 1/8" along the bottom. Trim off excess Tear & Tape. Remove the protective backing and adhere the piece of trim to the Tear & Tape. Trim off excess trim on the sides of the tag.
Cut a 4" piece of Petal Pink 5/8" Organdy Striped Ribbon.
Slide one end of the ribbon through the hole in the top of the tag. Pull the ribbon through until the ends are even.
Pull about 8" of string from the bottom edge of the Sahara Sand 5/8" Woven Threads Trim.
Tie the string around the ribbon at the top of the tag to cinch it in place. Tie a small bow. Trim the ends of the string and the ribbon.
Use Stampin' Dimensionals to adhere the tag to the center of the front of the card at a slight angle.
Use the mini spatula on the Take Your Pick to carefully peel up a diamond shaped gem from a sheet of Petal Pink Rhinestone Gems making sure that you get the adhesive backing as well. Adhere it to the center of the medallion circle.