Tags To Go Kitty Window Welcome

Supplies needed:

Project Recipe:

1. Cut cardstock and designer paper pieces to the following sizes using a Paper Trimmer:
   - card from Petunia Pop Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
   - 4" x 5-1/4" from Basic Black Two-Tone 12" x 12" Cardstock
   - 3" x 4-1/4" from Petunia Pop Cardstock
   - 2-7/8" x 4-1/8" of cat in window and front porch design from Spooky Sweet 12" x 12" Specialty Designer Series Paper, cut from the sheet of different designs so you cut off the jack o'lantern and bat on the right edge
   - 2" x 3-1/4" from Petunia Pop Cardstock

2. Cut cardstock and designer paper pieces to the following sizes using a Paper Trimmer:
   - card from Petunia Pop Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
   - 4" x 5-1/4" from Basic Black Two-Tone 12" x 12" Cardstock
   - 3" x 4-1/4" from Petunia Pop Cardstock
   - 2-7/8" x 4-1/8" of cat in window and front porch design from Spooky Sweet 12" x 12" Specialty Designer Series Paper, cut from the sheet of different designs so you cut off the jack o'lantern and bat on the right edge
   - 2" x 3-1/4" from Petunia Pop Cardstock

3. Insert the Basic Black Two-Tone rectangle into the Birch Wood 3D Embossing Folder so the lighter side of the cardstock is face up and you can read the logo on the front flap of the folder. . Use the line printed on the front flap of the folder to make sure it is lined up straight. Place the folder with the cardstock inside on the platform on your Stampin' Cut & Emboss Machine and run through the machine.

4. Adhere the cut down Spooky Sweet Designer Paper rectangle to the center of the Petunia Pop rectangle.

5. Adhere the matted designer paper rectangle to the center of the dry embossed Basic Black Two-Tone rectangle on the lighter side so it is centered side to side and is about 1/4" from the top.

6. Mount the "welcome home" sentiment from the Tags To Go Set on Block B. Ink it up with the Tuxedo Black Memento Pad. Stamp it on the horizontal Petunia Pop strip so it is centered top to bottom and slightly closer to one edge, leaving room to punch it out.

7. Unlock the Labeled With Love Punch. Hold the punch upside down so you can see the punching area. Slide the stamped sentiment into the punching area and get it lined up so it is centered. Punch. Leave the punch unlocked. Keep all the pieces.

8. Unlock the rectangular slit with a bump punch included in the Hole Punch Assortment. Hold the punch upside down so you can see the punching area. Slide the remaining end of the Petunia Pop strip into the punch and get it centered side to side. Punch. Leave the punch unlocked.

9. Hold the unlocked Labeled With Love Punch upside down so you can see the punching area. Slide the punched end of the Petunia Pop strip into the punching area one one end of the Labeled With Love Punch and get it lined up so it is centered over the punched slit. Punch. You don't need the entire punch, just enough to have the slit centered in the end.

10. Turn the punched sentiment label upside down. Place the punched out end bit with the slit punched in the center over one end of the punched sentiment label. Lightly outline the slit interior with a pencil or pen. Repeat on the other end.

11. Slide one end of the sentiment label punch out into the unlocked rectangular slit with a bump punch and get the penciled mark on one end centered in the punching area. Punch. Repeat on the other end. You should now have a sentiment label punch out with slits punched in either end to thread some ribbon through.

12. Cut a 5" piece of the Petunia Pop 1/4" Iridescent Ribbon.

13. Slide the punched sentiment label onto the ribbon and get it centered.

14. Put Stampin' Dimensionals on the back of the sentiment label punch out threaded onto the ribbon. Remove the protective backings and adhere the sentiment label punch out to the two-tone cardstock/matted designer paper rectangle so it is centered over the bottom of the designer paper rectangle.

15. Fold the ends of the ribbon over and secure the ribbon in place on the back of the two-tone cardstock with strips of Tear & Tape Adhesive.

16. Remove the protective backings from the Tear & Tape pieces and add Stampin' Seal to the back of the two-tone cardstock rectangle. Adhere the rectangle to the front of the Petunia Pop card.

17. Cut a 3-1/2" piece of the Petunia Pop 1/4" Iridescent Ribbon.

18. Slide one end of the ribbon under the ribbon already on the card front so it is on the left side of the sentiment label punch out. Tie in place with a half knot. Trim the ends.