Itty Bitty Greetings Snowflake Trio
S parkly Christmas card using Stampin' Up! products.
Cut cardstock, Glimmer Paper, and Multipurpose Adhesive Sheets pieces to the following sizes using a Stampin' Trimmer:
- card from Balmy Blue Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 4" x 5-1/4" from Tranquil Tide Cardstock
- 3-7/8" x 5-1/8" from Sparkle Glimmer Paper
- 2 pieces each 1-3/4" square from Balmy Blue Cardstock
- 2 pieces each 1-5/8" from Multipurpose Adhesive Sheets
- 2" square from Whisper White Cardstock
- scrap of Balmy Blue Cardstock at least 2-1/2" long
Use Tear & Tape Adhesive to adhere the Sparkle Glimmer Paper to the Tranquil Tide rectangle. Then, use SNAIL to adhere it to the front of the Balmy Blue card.
One at a time, carefully peel up the protective backing on one side of the Multipurpose Adhesive Sheet squares and adhere them to one side of the Balmy Blue squares. Leave the other protective backing pieces in place.
Place one Balmy Blue square on the Precision Base Plate on top of the Platform on the Big Shot so that the adhesive side (with protective backing in place) is on the bottom (blue facing up).
Pick out the medium-sized snowflake thinlit from the Seasonal Layers Thinlits. Place it on top of the Balmy Blue square on the Big Shot. Place a Cutting Pad on top and run through the Big Shot a couple of times. Use the Die Brush and Paper-Piercing Tool to remove the pieces.
Repeat the above 2 steps with the other square of Balmy Blue so you have two snowflake cut outs with adhesive on the backs.
One at a time, peel the protective backings off of the snowflake cut outs and adhere them to the front of the card in the middle so they are about 3/8" from the top and bottom edges.
Pick out the large-sized snowflake thinlit from the Seasonal Layers Thinlits. Place it on top of the Whisper White square on the Precision Base Plate on top of the Platform on the Big Shot. Place a Cutting Pad on top and run through the Big Shot a couple of times. Use the Die Brush and Paper-Piercing Tool to remove the pieces.
Mount the "'tis the season" sentiment from the Itty Bitty Greetings Set on Block G. Ink it up with the Tranquil Tide Ink Pad. Stamp it in the center of the scrap of Balmy Blue Cardstock.
Unlock the Classic Label Punch. Holding the punch upside down so you can see the punching area, slide the stamped sentiment into the punch and get it centered in the punching area. Punch.
Put a small strip of Tear & Tape Adhesive on the back of the sentiment punch out. Adhere it to the center of the white snowflake cut out.
Cut a 3-1/2" piece of Tranquil Tide 1/4" Velvet Ribbon so there are sharp angles on either end.
Lay the ribbon at an angle across the middle of the card so it is centered between the two blue snowflakes. Carefully put a small piece of Tear & Tape Adhesive under the ribbon at the same angle. Remove the protective backing and adhere the ribbon in place.
Put a Mini Stampin' Dimensional on either end of the sentiment punch out on the back where it sticks out past the snowflake. Remove the protective backings and adhere the snowflake with sentiment punch out to the center of the card front so it is centered over the ribbon strip half way between the two blue snowflakes.
Carefully peel up 2 pearl white sequins from a sheet of Basic Adhesive-Backed Sequins making sure that you get the adhesive backings as well. Adhere them to the centers of the blue snowflakes.