B right, cheery thank you card using new Stampin' Up! products.
Project Recipe
Cut cardstock pieces to the following sizes using a Paper Trimmer:
- card from Magenta Madness Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 4" x 5-1/4" from Whisper White Cardstock
- 2-7/8" x 3-3/8" from Just Jade Cardstock
- 2-3/4" x 3-1/4" from Whisper White Cardstock
- 3/4" x 2-3/4" from Whisper White Cardstock
Mount the single flower image from the Lovely You Set on Block A. Ink it up with the Magenta Madness Ink Pad. Stamp it randomly all over the 4" x 5-1/4" white rectangle. Remember to re-ink the stamp each time. Let some of the images go off the edges.
Insert the stamped white rectangle into the Scripty 3D Embossing Folder so the dry embossed lines will run horizontally across the vertical white rectangle. Use the line drawn on the front flap of the folder to help you line the cardstock up straight. Make sure the printed side (line and Stampin' Up! logo) of the folder and the flowers on the cardstock are all face up. Place the folder with the paper inside on your die cutting and embossing tool and run through the machine.
Adhere the stamped and dry embossed white rectangle to the front of the Magenta Madness card.
Mount the large, single flower on a stem with two little leaves image from the Lovely You Set on Block B. Ink up the petals of the flower using the brush tip of the Magenta Madness Marker. Ink up the stem, leaves, and base of the flower using the brush tip of the Just Jade Marker. Breathe on the stamp to moisten the ink. Stamp the flower on stem image in the center of the 2-3/4" x 3-1/4" white rectangle so the top of the flower is near the top of the top 2-3/4" edge.
WITHOUT RE-INKING, stamp the flower on stem image again just to the right and slightly below the first stamped image at a slight angle. Leave the stamp on the block.
Re-ink the flower on a stem image on Block B using the Markers again. Breathe on the stamp to moisten the ink. Stamp the flower on stem image just to the left and slightly below the first stamped flower on stem image at a slight angle.
Mount the single stem with lots of leaves image from the Lovely You Set on Block G. Ink it up with the Just Jade Ink Pad. Stamp it on the center of the stamped white rectangle so it is between two of the previously stamped flowers on stems images. Leave the stamp on the block!
WITHOUT RE-INKING, stamp the stem with lots of leaves image again just to the right and slightly below the first stamped stem with lots of leaves image at an angle. Leave the stamp on the block.
Re-ink the stem with lots of leaves image on Block G using the Just Jade Ink Pad again. Stamp the stem with lots of leaves image on Grid Paper. WITHOUT RE-INKING, stamp the image just to the left and slightly below the first stem with lots of leaves image at an angle.
If needed, use the fine tip of the Just Jade Marker to extend any stems for the flowers or leaves downward so they will be hidden behind the stamped sentiment in a later step.
Adhere the stamped white rectangle to the Just Jade rectangle.
Cut a 3-1/4" piece of Magenta Madness 2020-2022 In Color 1/4" Ribbon.
Lay the ribbon across the layered, stamped white cardstock so the ribbon is about 1/2" from the bottom edge. Flip the cardstock over and fold the ends of the ribbon over. Adhere the ends of the ribbon in place with pieces of Tear & Tape Adhesive.
Remove the protective backing from the Tear & Tape strips and add Stampin' Seal to the back of the Just Jade rectangle. Adhere it to the front of the card so it is evenly spaced on the top, left, and right edges.
Unlock the Lovely Labels Pick A Punch. Slide one short edge of the white strip into the left side of the punch (the side of the punch with the more rounded label top) as far as it will go. Punch. Slide the other end of the white strip into the same side of the punch as far as it will go and punch.
Mount one of the shorter sentiments from the Lovely You Set on Block G. Ink it up with the Magenta Madness Ink Pad. Stamp it in the center of the punched label.
Use the side of the brush tip of the Just Jade Marker to carefully outline the edges of the stamped sentiment label punch out.
Use Stampin' Dimensionals to adhere the sentiment label punch out to the front of the card so it is centered over the ribbon under the stamped flowers and leaves.
Use the mini spatula on the Take Your Pick to carefully peel up 2 Just Jade dots from a sheet of 2020-2022 In Color Enamel Dots making sure that you get the adhesive backings as well. Adhere them to either end of the sentiment label punch out in the centers.
Cut a 4" piece of the Magenta Madness 2020-2022 In Color 1/4" Ribbon.
Slide one end of the ribbon under the ribbon on the card front on the right side of the sentiment label punch out. Tie it in place using a half knot. Trim the ends.