T his is absolutely adorable, and you can substitute Hot Chocolate or Tea or any other K-Cup flavor.
Project Recipe
Cardstock:
Cinnamon Cider--7 3/4" x 7 3/4" square and score at 2 3/4" on each side.
Very Vanilla--4 1/4" x 4 1/4" square and score at 15/16" on each side. 2 1/8" x 1 5/8" (2), 2 1/4" x 2 1/4" (1 3/4" scallop circle die), 5/8" x 1 3/4", 2" x 2 1/4" (cut on diagonal)
Early Espresso--5" x 5" square and score at 1/2" and 1 1/2" on each side.
World of Good Specialty DSP--2" x 2 1/2" (3), these next pieces can be a different DSP 2" x 2 1/4" (cut on diagonal), 2" x 1 1/2" (1)
Copper Foil--2 1/8" x 2 5/8" (3), 1 1/4" x 1 3/4" (die cut coffee)
Adhesive Sheet--1 1/4" x 1 3/4" (adhere to foil, then die cut coffee)
Inside of the box:
Cinnamon Cider Cardstock cut to 7 3/4" x 7 3/4" scored at 2 3/4" on each side, fold at all score lines using Bone Folder, then cut away all the corners. I used one of these corner scrapes to stamp the cup with Cinnamon Cider Ink and then die cut.
Box Lid:
Very Vanilla Cardstock cut to 4 1/4" x 4 1/4" scored at 15/16" on each side, fold at all score lines using Bone Folder, then cut each corner at an angle from score line to score line, as shown. Fold the tabs in and adhere with Multipurpose Liquid Glue, creating a lid for the box.
K-Cup Holder:
Early Espresso Cardstock cut to 5" x 5" square and score at 1/2" x 1 1/2" on each side, fold at all score lines using Bone Folder, then cut all corners away as shown.
Using the 1 5/8" circle die cut as shown.
Adhere tear and tape, as shown. The side that has three strips of tape is the inside back of the K-Cup Holder. This is where the holder attaches to the back flap of the Cinnamon Cider Box. Set aside.
Using the piece of DSP that is 2" x 1 1/2" adhere to Very Vanilla 2 1/8" x 1 5/8", as shown. Also adhere the die cut coffee cup, as shown.
Using the DSP that is 2" x 2 1/4", cut it at a diagonal using your paper Trimmer, cut the Very Vanilla piece that is 2 1/8" x 2 3/8" at a diagonal. You will only use one of each diagonal for this project. Adhere the diagonal DSP to the Very Vanilla, as shown. When you adhere the diagonal piece to the inside, front flap ONLY apply adhesive to the two sides edges creating a pocket. I cut tear and tape strip in half. The second piece of Very Vanilla (2 1/8" x 1 5/8") will tuck inside the pocket.
Adhere the DSP to the Foil x 3. Adhere two of these to the inside, left and right sides of the box.
Adhere the pieces to the top and the adhere the pocket, as previously described.
Stamp the sentiment, onto 1/2" x 2" piece of Very Vanilla with Cinnamon Cider. Adhere the DSP/Foil piece to the front outside of the box, then add the sentiment with dimensional. See diagram.
Fold the Early Espresso K-Cup holder and burnish well with Bone Folder on all the score lines. Remove the tear and tape adhesive strips and adhere to the inside bottom of the box. BE SURE TO PLACE THE SECTION OF THE BOX WITH 2 STRIPS OF ADHESIVE TO THE BACK OF THE BOX, LIFTING THE BACK FLAP TO ADHERE IT.
Die cut 1 3/4" Scalloped Circle from Very Vanilla.
Place adhesive strip on the back of the foil and die cut "Coffee". Adhere to the center of the scalloped circle.
Adhere these to the front of the K-Cup holder, placing glue on the bottom half of the scalloped circle.
Use a 22" piece of 3/8" Gold Metallic Edge Ribbon to tie the box closed.