S imple black and white card using Stampin' Up! products.
Project Recipe
Cut cardstock pieces to the following sizes using a Paper Trimmer:
- card from Whisper White Thick Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 4" x 5-1/4" from Basic Black Cardstock
- 2 pieces each 2-1/4" square from Whisper White Cardstock
- 1" x 3-1/4" from Whisper White Cardstock
Insert the Basic Black rectangle into the Subtle 3D Embossing Folder. Use the line drawn on the front of the folder to help you line the cardstock up straight. Place the folder with the paper inside on your die cutting and embossing tool and run through the machine.
Adhere the dry embossed black rectangle to the front of the Whisper White Thick card.
Pick out the black and white striped small card from the Come Sail Away Memories & More Card Pack. Adhere it to the front of the card so it is centered and the stripes are horizontal on the horizontal card.
Cut a 3-1/2" long piece of Whisper White 5/8" Flax Ribbon so it has a sharp angle on the left end.
Put a 2-1/2" strip of Tear & Tape Adhesive on the bottom of the Come Sail Away Memories & More Card so the bottom of the adhesive is about 1/2" from the bottom edge and the right edge is even with the right edge of the Come Sail Away Memories & More Card.
Remove the protective backing from the Tear & Tape strip on the card front and adhere the ribbon to it so the angled end is on the left and the tip of the angle almost touches the left edge of the Come Sail Away Memories & More Card and the bottom edge of the ribbon is about 1/4" from the bottom edge of the Come Sail Away Memories & More Card. Trim off excess ribbon on the right edge if needed.
Mount the single line sentiment of choice from the Itty Bitty Greetings Set on Block G. Ink it up with the Memento Pad. Stamp it on one end of the thin strip of Whisper White, but leave room to punch it out.
Unlock the Classic Label Punch. Hold it upside down so you can see the punching area. Slide the stamped sentiment into the punch and get it centered in the punching area. Punch.
Adhere the punched out sentiment to the center of the ribbon so the left point is about 1" from the left side of the Come Sail Away Memories & More Card.
Mount the single magnolia bud image from the Good Morning Magnolia Set on Block C. Ink it up with the Memento Pad. Stamp it in the center of one of the white squares. Re-ink the stamp with the Memento Pad and stamp in the center of the other white square.
Pick out the single bud die from the Magnolia Memory Dies. Put it on top of one of the stamped bud images on a platform on your cutting and embossing tool so the bud image is centered. Run through the tool. Repeat with the other bud image.
Use SNAIL to adhere one of the bud cut outs to the front of the card so the top of the bud is facing slightly towards the upper left corner of the card and it overlaps the right end of the sentiment punch out.
Use Stampin' Dimensionals to adhere the other bud cut out to the front of the card so it overlaps the first bud and the lower right corner of the Come Sail Away Memories & More Card and faces the other direction.
Cut an 8" piece of Whisper White Solid Baker's Twine.
Tie a small bow in the center of the twine. Trim the ends.
Use a Mini Glue Dot to adhere the bow to the center of the popped up bud's stem at the top of the stem.
Use the mini spatula on the Take Your Pick to carefully peel up 1 large rhinestone from a sheet of Rhinestone Basic Jewels making sure that you get the adhesive backing as well. Adhere it in the upper left corner of the Come Sail Away Memories & More Card.