P retty card using Stampin' Up! products.
Project Recipe
Cut cardstock, Glimmer Paper, and Multipurpose Adhesive Sheets pieces to the following sizes using a Stampin' Trimmer:
- card from Petal Pink Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 4" x 5-1/4" from Calypso Coral Cardstock
- 3-7/8" x 5-1/8" from Whisper White Cardstock
- 2-1/4" x 3-3/4" from Petal Pink Cardstock
- 1-3/4" x 3-1/2" from Calypso Coral Cardstock
- 1-5/8" x 3-3/8" from Multipurpose Adhesive Sheets
- 2" square from Sparkle Glimmer Paper
Insert the Whisper White rectangle into the Subtle Dynamic Textured Impressions Embossing Folder. Use the thin line drawn on the front flap of the folder to help you line up the cardstock and get it straight. Place the folder with the cardstock inside directly on your Big Shot Platform at the lowest possible setting. Place a Cutting Pad on top of the folder and run through the Big Shot.
VERY IMPORTANT: You are using only ONE Cutting Pad. If you try to use two, the sandwich will be too thick and you could damage the Big Shot.
Place the dry embossed white rectangle on some Grid Paper to protect your work surface from ink.
Mount the "wish" sentiment from the Follow Your Dreams Set on Block G. Ink it up with the Calypso Coral Ink Pad. Stamp it in the lower right corner of the dry embossed white rectangle.
Mount the sunburst flower image from the Follow Your Dreams Set on Block A. Ink it up with the Calypso Coral Ink Pad. Stamp it multiple times across the bottom of the dry embossed white rectangle at an angle from the lower left corner to about 3" from the bottom on the right side. Remember to re-ink the stamp each time. Let some of the images go off the edge. Clean the stamp with the Stampin' Mist and Stampin' Scrub, but leave it on the block.
Ink up the sunburst flower image with the Petal Pink Ink Pad. Stamp it multiple times across the bottom of the dry embossed white rectangle at an angle from the lower left corner to about 3" from the bottom on the right side. Remember to re-ink the stamp each time. Let some of the images go off the edge. Let some of the images overlap over images.
Adhere the stamped, dry embossed white rectangle to the large Calypso Coral rectangle and then to the front of the Petal Pink card.
Mount the dream catcher image from the Follow Your Dreams Set on Block I. Ink it up with the Calypso Coral Ink Pad. Stamp it in the center of the Petal Pink rectangle.
Pick out the matching, open, dream catcher framelit from the Chase Your Dreams Framelits. Place the stamped dream catcher image on the Cutting Pad on top of the Magnetic Platform on the Big Shot. Place the dream catcher framelit on top so it is centered over the dream catcher image. Place another Cutting Pad on top and run through the Big Shot.
Pick out the detailed, circular thinlit from the Chase Your Dreams Framelits. Place it on top of the cut out dream catcher image on the Precision Base Plate on top of the Platform on the Big Shot so the circle thinlit is lined up over the circle on the top of the dream catcher. Place a Cutting Pad on top and run through the Big Shot a couple of times. Use the Die Brush to remove the pieces.
Carefully peel up the protective backing on one side of the Multipurpose Adhesive Sheet and adhere the adhesive sheet to one side of the small Calypso Coral rectangle. Leave the other protective backing piece in place.
Place the Calypso Coral rectangle on the Precision Base Plate on top of the Platform on the Big Shot so that the adhesive side (with protective backing in place) is on the bottom (Calypso Coral facing up).
Pick out the smaller, detailed dream catcher thinlit from the Chase Your Dreams Framelits. Place it on top of the Calypso Coral rectangle on the Big Shot. Place a Cutting Pad on top and run through the Big Shot a couple of times. Use the Die Brush and Paper-Piercing Tool to remove the pieces.
Peel the protective backing off of the smaller dream catcher cut out and adhere it to the center of the larger dream catcher cut out.
Pick out the open circle framelit from the Chase Your Dreams Framelits. Place the square of Sparkle Glimmer Paper on the Cutting Pad on top of the Magnetic Platform on the Big Shot. Place the circle framelit on top. Place another Cutting Pad on top and run through the Big Shot.
Put a Mini Glue Dot on the back of the larger dream catcher cut out in the center of the filigree circle. Adhere the Glimmer Paper circle to the back of the larger dream catcher cut out so it is centered behind the filigree circle.
Use Stampin' Dimensionals to adhere the dream catcher to the upper left side of the card front.
Carefully peel up a Petal Pink sequin from a sheet of Basic Adhesive-Backed Sequins making sure that you get the adhesive backing as well. Adhere it to the center of the filigree circle on the dream catcher.
Carefully peel up 5 more Petal Pink sequins from a sheet of Basic Adhesive-Backed Sequins making sure that you get the adhesive backings as well. Adhere them randomly along the stamped line of sunburst flower images going diagonally across the bottom of the card.
Carefully peel up a Grapefruit Grove pearl from a sheet of Share What You Love Artisan Pearls making sure that you get the adhesive backing as well. Adhere it to the center of the sequin in the center of the filigree circle on the dream catcher.
Carefully peel up 3 more Grapefruit Grove pearls from a sheet of Share What You Love Artisan Pearls making sure that you get the adhesive backings as well. Adhere them randomly along the stamped line of sunburst flower images going diagonally across the bottom of the card.