P retty card perfect for a fellow paper crafter using Stampin' Up! products.
Project Recipe
Cut cardstock and designer paper pieces to the following sizes using a Paper Trimmer:
- card from Boho Blue Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 4" x 5-1/4" from Misty Moonlight Cardstock
- 3-7/8" x 5-1/8" from Basic White Cardstock
- 1-1/2" x 5-1/8" of blue flowers and leaves on white background design from Countryside Inn 12" x 12" Designer Series Paper
- 2-1/4" x 2-3/4" from Basic White Cardstock
- 1-3/4" x 2-3/4" from Misty Moonlight Cardstock
-1" x 2" of lines of blue stitching on light blue background design from Countryside Inn 12" x 12" Designer Series Paper, cut so the lines are horizontal on the horizontal rectangle
- 1" x 1-1/2" from Boho Blue Cardstock
As you are ready to stamp using the Crafting With You Set, place the cardstock on the Stampin' Pierce Mat. Using the mat will help you get a cleaner image each time you stamp.
Mount the sentiment of choice from the Crafting With You Set on an appropriate size block. Ink it up with the Boho Blue Ink Pad. Stamp it in the upper right corner of the horizontal 3-7/8" x 5-1/8" white rectangle.
Adhere the 1-1/2" x 5-1/8" strip of floral Countryside Inn Designer Paper to the bottom of the stamped white layer so the left, right, and bottom edges are even.
Adhere the stamped white rectangle with designer paper attached to the center of the 4" x 5-1/4" Misty Moonlight rectangle.
Cut a 6" piece of the Misty Moonlight 3/8" Inner Braid Ribbon.
Lay the ribbon across the layered cardstock/designer paper rectangle so it covers the seam between the designer paper and white layers. Fold the ends of the ribbon over and secure the ribbon in place on the back with strips of Tear & Tape Adhesive.
Remove the protective backings from the Tear & Tape pieces and add Stampin' Seal to the back of the Misty Moonlight rectangle. Adhere the rectangle to the front of the Boho Blue card.
Pick out the solid paper trimmer die from the Crafting With You Dies. Put it on top of the 1-3/4" x 2-3/4" Misty Moonlight rectangle on a platform on your Stampin' Cut & Emboss Machine. Run through the machine. Use the Take Your Pick to remove the pieces as needed. Make sure to save the tiny square cut out with the die.
Carefully slide the 1" x 2" striped Countryside Inn Designer Paper strip into the paper trimmer cut out as shown.
Adhere the paper trimmer cut out with designer paper on it to the front of the card as shown so it is just to the left of the sentiment and overlaps the ribbon and designer paper a bit.
Use Multipurpose Liquid Glue or Fine-Tip Glue Pen to adhere the tiny square cut out with the paper trimmer die to the center of the slit just above the designer paper as the cutting blade on the trimmer.
Mount the Stampin' Cut & Emboss Machine image from the Crafting With You Set on Block D. Ink it up with the Boho Blue Ink Pad. Stamp it on the 2-1/4" x 2-3/4" white rectangle.
Pick out the matching, open Cut & Emboss Machine die from the Crafting With You Dies. Put it on top of the stamped image on a platform on your Stampin' Cut & Emboss Machine so it is centered over the image. Run through the machine.
Use Stampin' Dimensionals to adhere the Cut & Emboss Machine cut out to the front of the card as shown so it is just above the ribbon and overlaps the left side of the paper trimmer cut out.
Pick out the set of two solid hearts die and the small open heart die from the Crafting With You Dies. Put them on top of the 1" x 1-1/2" Boho Blue rectangle on a platform on your Stampin' Cut & Emboss Machine. Make sure the dies do NOT overlap. Run through the machine. Use the Take Your Pick to remove the pieces as needed.
Use Multipurpose Liquid Glue or Fine-Tip Glue Pen to adhere the tiny heart cut outs in place as shown.
Cut a 3-1/2" piece of the Misty Moonlight 3/8" Inner Braid Ribbon.
Tie a half knot in the center of the ribbon. Trim the ends.
Use a Mini Glue Dot to adhere the ribbon knot to the front of the card at a slight angle as shown.