3-Panel Card with Black & White DSP

{ tams # 73077 }

Print Recipe

CS=Card Stock
TOMBO= Multipurpose Liquid Adhesive
All dimensions are in inches
DSP=Designer Series Paper

Cutting and Scoring:

Basic White CS:
--Card Base: Cut 1 @ 5-1/2 x 12
--Score base parallel to the short side at 4" and 8" fold in an accordion or z-fold way ie: 4" is mountain fold and 8" is valley fold. See picture
--White Front Matte: Cut 1 @ 2-1/8 x 4-1/2
--Inside Middle Sentiment Piece: Cut 1 @ 3-1/2 x 5
--White Inside Matte: Cut 1 @ 1-5/8 x 3-3/4
--Enough for the inside white lable punched piece
--Enough for a white 2-1/2" Circle die from the stylish Shapes Dies or a 2-1/2" Circle punch

Basic Black CS:
--Cut one at 3-3/4 x 5-1/4
--Punch one label cut in half front the straight sid to the straight side
--Die cut largest stitched square from the Stylish Shapes dies or one that is approx 2-3/4 square.

DSP Cut 1 of each--Watch the directions of the prints!!
--Cut front striped print at 3-3/4 x 5-1/4
--Cut Inside zig zag print at 3-3/4 x 5-1/4
--Cut front zig zag strip at 2 x 4-3/8
--Cut inside striped print 3-5/8 x 1-1/2

Very Best Trio Punch is tricky...follow the directions below to get all the corners of the middle inside piece punched CORRECTLY:
--CS FACE UP: Punch ONLY 2 corners diagonal from each other (one top right one bottom left) with the corner punch from Very Best Trio THEN....
--FLIP CS OVER so the back is now up and punch the other corners

Stamping, Die Cutting, and Punching:

If you want to make multiples, use the Stamparatus! If only making one, then stop after die cutting the raccoon and move on to the "Finishing the Stamping" step.

Making Multiples for this card:
--Cut CS to desired size
--Place on the Stamparatus all the way in the corner
--Place stamp where you want it to stamp and pick it up with the Stamparatus Plate
--Stamp the raccoon in Memento Black ink.
--LEAVE STAMP on the plate but clean off stamp using shammy.

--Die cut the raccoon
--Tape negative CS piece to Small Grid Paper as shown
--Die cut a bunch of blank Circles using the Stylish Shapes Dies
--Insert a die cut blank
--Stamp the blanks
--Clean stamp in between stamping each blank

Finish the Stamping:
--Stamp the inside Basic White piece with desired sentiment or write in it. Use Memento Black Ink.
--Stamp the Basic White piece of scrap for the left inside label and punch out with the Label Me Lovely Punch. Use Memento Black Ink.
--Stamp the outside of envelope if you wish

Putting it all together!
See pictures for placement. Use Multipurpose Liquid Glue (TOMBO) for the following:
--Adhere the front and the left inside DSP to the Card Base
--Adhere the DSP strips to their proper White Mattes
--Adhere the DSP matted combos to the correct front / left inside DSP
--Adhere the Black square die cut to the front mattes / DSP's
--Color the grass with Dark Granny Apple Green Stampin' Blend marker
--Put Brushed Brass Butterflies, and the Fun Flower Resin Shapes on the raccoon circle die with the Take Your Pick tool
--Adhere raccoon circle die cut with Stampin' Dimensionals.
--Adhere the Basic Black Matte to the inside Middle Card Base
--Adhere the Middle White on top using Stampin' Seal
--Adhere the 1/2 pieces of Label Me Lovely Black CS to the top and bottom of the white punched sentiment using Stampin' Seal+
--Adhere that to the left inside DSP's with Seal+
--Tie a bow with my Bow Maker or your finger and
--Adhere that with a folded Mini Glue Dot.