P retty party favor/treat boxes decorated with Stampin' Up! products.
Project Recipe
Cut cardstock and Adhesive Sheets pieces to the following sizes using a Paper Trimmer:
- 2" square from Just Jade Cardstock
- 1-7/8" square from Adhesive Sheets
- 1-1/4" x 2-1/2" from Magenta Madness Cardstock
- scraps of Magenta Madness Cardstock big enough to cut out the flowers for the square die you used
Pull out one white box bottom from the Simply Classic Treat Boxes. Pop it open. Fold the long white flap on the inside down into the box. Fold the two side flaps into the box. Fold the long flap with a rounded end flap down and tuck the rounded end flap into the space between the first white flap and the side of the box.
Pull out one gold box top from the Simply Classic Treat Boxes. Pop it open. Fold the long white flap on the inside down into the box. Fold the two side flaps into the box. Fold the long flap with a rounded end flap down and tuck the rounded end flap into the space between the first white flap and the side of the box.
Put a treat into the white box bottom. Slide the gold box top over the white box bottom.
Peel the protective backing off of the Adhesive Sheets square. Adhere the Adhesive Sheets square to one side of the Just Jade square. Be sure to leave the other protective backing in place for now.
Tip: Use the paper-piercing tool on the Take Your Pick tool to help peel up the protective backing if needed.
Pick out one of the floral squares from the Floral Squares Dies. Put it on top of the Just Jade square on a platform on your Stampin' Cut & Emboss Machine so the Just Jade (green) side is face up. Run through the machine. Use the Take Your Pick Die Brush Tip and paper-piercing tool on the Take Your Pick to remove the pieces.
Carefully remove the protective backing from the floral square cut out. Adhere it to the panel on the front of the gold box top.
Pick out the matching flower top die(s) from the Floral Squares Dies. Put them on top of the Magenta Madness scrap on a platform on your Stampin' Cut & Emboss Machine. Make sure the dies do NOT overlap if using multiple dies. Run through the machine. Use the Take Your Pick Die Brush Tip and paper-piercing tool on the Take Your Pick to remove the pieces.
Tip: If you are using the large starburst flower, you will need to cut two of them out.
Use Multipurpose Liquid Glue or Fine-Tip Glue Pen to adhere the flower cut outs in place over the green flowers on the floral square cut outs.
Tip: If you are using the starburst flowers, cut one of the flowers apart so there are 3 petals on one side and 4 petals on the other side. Adhere the 3 petal piece to the top half flower on the flower cut out. Then, adhere the 4 petal piece on top of it slightly offset.
Use the mini spatula on the Take Your Pick to carefully peel up small or medium gems from a sheet of Gilded Gems making sure that you get the adhesive backings as well. Adhere them to the centers or bottoms of the flowers as shown.
Mount the "For You" sentiment from the A Wish For Everything Set on Block A. Ink it up with the Just Jade Ink Pad. Stamp the sentiment in the center of the remaining Magenta Madness strip.
Pick out the smallest rounded top tag die from the Tailor Made Tags Dies that cuts out a tag that is 3/4" wide. Put it on top of the stamped sentiment rectangle on a platform on your Stampin' Cut & Emboss Machine so the sentiment is centered in the die and is about 3/8" from the hole in the top of the tag with the top of the tag on the left side. Run through the machine.
Use Paper Snips Scissors to cut off the end of the tag about 1/4" below the sentiment.
Cut a 5" piece of the Just Jade & Gold 3/8" Braided Ribbon so it has sharp angles on the ends.
Feed one end of the ribbon through the loop of white ribbon at the top of the box. Feed the tag onto the end of the ribbon. Tie the ribbon in place with a half knot. Trim the ends of the ribbon.