V intage style thinking of you card using Stampin' Up! products.
Project Recipe
Cut cardstock and designer paper pieces to the following sizes using a cutting and scoring tool:
- card from Rococo Rose Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 4" x 5-1/4" from Seaside Spray Cardstock
- 2-1/2" x 5-1/8" of light tan textile design from Woven Threads Designer Series Paper
- 1-1/2" x 5-1/8" of pink, purple, and light blue vintage fabric design from Woven Threads Designer Series Paper
- 1-3/4" x 6" from Purple Posy Cardstock
- 1-1/2" x 3-3/4" from Very Vanilla Cardstock
- scrap of Rococo Rose Cardstock at least 3/4" square
Mount the small leafy flourish image from the Woven Heirlooms Set on Block A. Ink it up with the Rococo Rose Ink Pad. Stamp it in the lower right corner of the light tan piece of Woven Threads Designer Paper.
Adhere the stamped piece of designer paper to the Seaside Spray rectangle so about 1/16" of blue shows on the top, right, and bottom edges.
Pick out the vine-like lace die from the Delicate Lace Dies. Put it on top of the long strip of Purple Posy Cardstock on a platform on your cutting and embossing tool. Run through the tool. Use the Take Your Pick Die Brush Tip and paper-piercing tool on the Take Your Pick to remove the pieces.
Adhere the strip of pink, purple, and light blue fabric designer paper to the long, bottom edge of the Purple Posy lace cut out so the stitched edge of the die cut out is right along a long edge of the designer paper. Trim off excess cardstock on the ends using Paper Snips.
Adhere the strip of designer paper with lace cut out attached to the Seaside Spray rectangle so it covers the left edge of the tan designer paper already on the rectangle.
Cut a 6" piece of the Very Vanilla 3/8" Scalloped Lace Trim.
Lay the trim across the cardstock/designer paper layers so it covers the edge between the lace cut out and the pink, purple, and blue fabric designer paper. Flip the layers over and fold the ends of the trim over. Adhere the ends of the trim in place with pieces of Tear & Tape Adhesive.
Remove the protective backing from the Tear & Tape strips and add SNAIL to the back of the Seaside Spray rectangle. Adhere it to the front of the Rococo Rose card.
Mount the "thinking of you" sentiment from the Woven Heirlooms Set on Block H. Ink up only the word "thinking" using the side of the brush tip of the Rococo Rose Marker. Breathe on the stamp to moisten the ink. Stamp in the center of the vanilla strip. Clean the stamp using the Simply Shammy and/or Stampin' Mist and Stampin' Scrub, but leave it on the block.
Ink up only the words "of you" using the side of the brush tip of the Seaside Spray Marker. Breathe on the stamp to moisten the ink. Stamp in the center of the vanilla strip so the "o" in the word "of" is right below the "k" in the already stamped word "thinking." Some of the letters on the two parts of the sentiment will overlap.
Pick out the long, open label die with leaf shapes cut from each end from the Stitched Labels Dies. Put it on top of the stamped sentiment rectangle on a platform on your cutting and embossing tool so it is centered over the sentiment. Run through the tool. Use the Take Your Pick Die Brush Tip and paper-piercing tool on the Take Your Pick to remove the pieces if needed.
Use Stampin' Dimensionals to adhere the senitment label cut out to the front of the card so it is about 1-3/8" from the top and about 3/4" from the left edge.
Pick out the tiny heart die from the Stitched Labels Dies. Put it on top of the scrap of Rococo Rose Cardstock on a platform on your cutting and embossing tool. Run through the tool. Use the Take Your Pick Die Brush Tip and paper-piercing tool on the Take Your Pick to remove the pieces if needed.
Use a Mini Glue Dot to adhere the heart cut out to the bottom left edge of the sentiment label cut out at a slight angle. Some of the heart cut out will hang over the bottom edge of the sentiment label cut out.
Squeeze a tiny amount of Multipurpose Liquid Glue onto the Silicone Craft Sheet.
Use the tacky putty tip of the Take Your Pick to pick up some different sizes and colors of sequins from the Woven Threads Sequin Assortment. Dip them very lightly onto the glue on the Silicone Craft Sheet to get a small amount of glue on the back of each sequin. Then, place it on the card front where you want it and adhere in place. Put one large sequin at the top of the small flourish stamped in the lower right corner. Put one tiny sequin on the bottom left side of the tiny heart cut out. Adhere two more close to each other just above the sentiment label cut out in the upper right corner. Adhere one more somewhere on the fabric designer paper on the lower left side.