S ummery thank you card using Stampin' Up! products.
Project Recipe
Cut cardstock and Adhesive Sheets pieces to the following sizes using a Paper Trimmer:
- card from Bumblebee Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 4" x 5-1/4" from Daffodil Delight Cardstock
- 2-1/4" x 2-1/2" from Bumblebee Cardstock
- 2-1/8" x 2-3/8" from Adhesive Sheets
- 2-1/2" x 2-3/4" from Shaded Spruce Cardstock
- 2-3/8" x 2-5/8" from Adhesive Sheets
- 1-1/4" x 2-1/4" from Very Vanilla Cardstock
Insert the Daffodil Delight rectangle into the Dainty Diamonds 3D Embossing Folder. Place the folder with the paper inside on your Stampin' Cut & Emboss Machine platform and run through the machine.
Adhere the dry embossed Daffodil Delight rectangle to the front of the Bumblebee card.
Peel the protective backing off of the 2-1/8" x 2-3/8" Adhesive Sheets rectangle. Adhere the Adhesive Sheets rectangle to one side of the Bumblebee rectangle. Be sure to leave the other protective backing in place for now.
Pick out the large, detailed, bottom of the pineapple die from the In The Tropics Dies. Put it on top of the Bumblebee rectangle on a platform on your Stampin' Cut & Emboss Machine so the Bumblebee (yellow) side is facing up. Run through the tool. Use the Take Your Pick Die Brush Tip and Take Your Pick to remove the pieces.
Carefully remove the protective backing from the back of the detailed Bumblebee bottom of the pineapple cut out and adhere it to the front of the card so the bottom of the pineapple cut out is about 1/2" from the bottom of the card and the left side is about 1/2" from the left side of the card. Make sure the triangular cut out bits are pointing upwards.
Peel the protective backing off of the 2-3/8" x 2-5/8" Adhesive Sheets rectangle. Adhere the Adhesive Sheets rectangle to one side of the Shaded Spruce rectangle. Be sure to leave the other protective backing in place for now.
Pick out the large, detailed, top leaves of the pineapple die from the In The Tropics Dies. Put it on top of the Shaded Spruce rectangle on a platform on your Stampin' Cut & Emboss Machine so the Shaded Spruce (green) side is facing up. Run through the tool. Use the Take Your Pick Die Brush Tip and Take Your Pick to remove the pieces.
Carefully remove the protective backing from the back of the detailed Shaded Spruce top leaves of the pineapple cut out and adhere it to the front of the card so it is centered over the top of the pineapple bottom cut out.
Mount the "thank you" or "hello" sentiment from the Timeless Tropical Set on Block B. Ink it up with the Bumblebee Ink Pad. Stamp it in the center of the small Very Vanilla strip.
Pick out the small, skinny, stitched label die with rounded ends from the Ornate Frames Dies. Put it on top of the stamped sentiment on a platform on your Stampin' Cut & Emboss Machine so the sentiment is centered (there will be a bit of empty space on the lower right side if you use the "thank you" sentiment). Run through the tool.
Adhere the sentiment cut out to the card front so it overlaps the lower right side of the pineapple cut out a bit and is about 1" from the bottom of the card.
Carefully remove two of the tiny, wooden x elements from the wood of the In Good Taste Elements. Press the back of the x elements to the roll of Mini Glue Dots to get glue dots on the back of the elements. Squish the edges of the glue dots in a bit with your fingers. Adhere one x element to the front of the card so it overlaps the lower right side of the sentiment cut out. Adhere the other x element to the front of the card so it is centered over the bottom of the Shaded Spruce top leaves of the pineapple cut out.