P retty treat bags made with Stampin' Up! products.
Project Recipe
Cut cardstock and Foil Sheets pieces to the following sizes using a Paper Trimmer:
- 2" x 5" from Whisper White Cardstock
- 2-3/4" x 3" from Whisper White Cardstock
- 2-1/2" square from Garden Green Cardstock
- 1-1/2" x 2-1/4" from Copper Foil Sheets
- 1-1/2" x 2-3/4" from Night of Navy Cardstock
- 1-1/2" x 2-3/4" from Copper Foil Sheets
Insert treat into Copper Dotted Treat Bag. Fold the top of the bag over.
Unlock the Delightful Tag Topper Punch. Slide one short edge of the 2" x 5" strip of Whisper White Cardstock into the punch as far as it will go. Punch.
As you are ready to stamp using the So Many Stars Photopolymer Set, place the cardstock on the Stampin' Pierce Mat. Using the mat will help you get a cleaner image each time you stamp.
Mount the "JOY" sentiment from the So Many Stars Set on Block B. Ink it up with the Garden Green Ink Pad. Stamp it on the bottom of the punched white tag in the center.
Mount the top of the snowglobe image from the Still Scenes Set on Block D. Ink it up with the Night of Navy Ink Pad. Stamp in the center of the remaining white rectangle.
Pick out the top of the snowglobe die from the Snow Globe Scenes Dies. Put it on top of the stamped top of the snowglobe image on a platform on your cutting and embossing tool so the image is centered. Run through the tool.
Pick out the three pine trees die from the Snow Globe Scenes Dies. Put it on top of the Garden Green square on a platform on your cutting and embossing tool. Run through the tool. Use the Take Your Pick Die Brush Tip and paper-piercing tool on the Take Your Pick to remove the pieces.
Adhere the three pine trees cut out to the top of the snowglobe cut out so the trees are at the bottom.
Pick out the deer die from the Snow Globe Scenes Dies. Put it on top of the small Copper Foil Sheets rectangle on a platform on your cutting and embossing tool. Run through the tool. Use the Take Your Pick Die Brush Tip and paper-piercing tool on the Take Your Pick to remove the pieces.
Use the Bone Folder to burnish the deer cut out to smooth out any marks made by the die.
Use the Fine-Tip Glue Pen or Mulitpurpose Liquid Glue to adhere the copper foil deer cut out to the top of the snowglobe cut out so the deer is at the bottom and overlaps the trees.
Put strips of SNAIL vertically down the center of the back of the snowglobe top. Adhere it to the top of the white tag.
Pick out the open snow globe base die from the Snow Globe Scenes Dies. Put it on top of the Night of Navy rectangle on a platform on your cutting and embossing tool. Run through the tool.
Pick out the filigree snow globe base die from the Snow Globe Scenes Dies. Put it on top of the remaining larger Copper Foil Sheet rectangle on a platform on your cutting and embossing tool. Run through the tool. Use the Take Your Pick Die Brush Tip and paper-piercing tool on the Take Your Pick to remove the pieces.
Use the Fine-Tip Glue Pen or Mulitpurpose Liquid Glue to adhere the copper foil filigree snowglobe base cut out to the top of the Night of Navy snowglobe base cut out.
Put strips of SNAIL across the center of the back of the layered snowglobe base. Adhere to the tag so it overlaps the bottom of the snowglobe top.
Adhere the tag to the front of the treat bag at a slight angle.
Pick out a white Mini Library Clip. Attach it to the top of the bag at the top of the tag.
Cut a 3-1/2" piece of the Garden Green 3/8" Double-Stitched Ribbon.
Tie a half knot in the center of the ribbon. Trim the ends
Use a Mini Glue Dot to adhere the ribbon knot to the top of the tag just below the library clip.