F un Halloween treats using Stampin' Up! products.
Project Recipe
Cut cardstock and designer paper pieces to the following sizes using a Stampin' Trimmer:
- 2" x 3-1/4" from Very Vanilla Cardstock
- 2-1/2" x 3-1/2" of wavy orange on vanilla pattern from Spooky Night Designer Series Paper
- scrap of Lemon Lime Twist Cardstock at least 1-1/2" wide
- scrap of Very Vanilla Cardstock at least 1-1/4" wide
- witch hat image cut from a piece of Spooky Night Designer Series Paper
Mount the potion bottles outline image from the Spooky Cat Set on Block A. Ink it up with the Basic Black Archival Ink Pad. Stamp it about 1/2" up from the bottom of the vanilla rectangle.
Mount the small round bottle inside potion image on Block A. Ink it up with the Lemon Lime Twist Ink Pad. Stamp it inside the small round bottle outline.
Mount the small triangular bottle inside potion image on Block A. Ink it up with the Cajun Craze Ink Pad. Stamp it inside the triangular bottle outline.
Mount the large round bottle inside potion image on Block A. Ink it up with the Pumpkin Pie Ink Pad. Stamp it inside the large round bottle outline.
Pick out the smooth oval framelit from the Layering Ovals Framelits that cuts out a smooth oval that is 1-1/4" wide. Place the stamped potions rectangle on the Cutting Pad on top of the Magnetic Platform on the Big Shot. Place the smooth oval framelit on top so the potion bottles are centered side to side as close to the bottom of the oval as possible. Place another Cutting Pad on top and run through the Big Shot.
Pick out the scalloped oval framelit from the Layering Ovals Framelits that cuts out a scalloped oval that is 2" wide. Place the designer paper rectangle on the Cutting Pad on top of the Magnetic Platform on the Big Shot. Place the scalloped oval framelit on top. Place another Cutting Pad on top and run through the Big Shot.
Adhere the vanilla oval with the potions stamped on it to the center of the scalloped, designer paper oval so the wavy orange pattern is face up.
Use the 1/8" Handheld Circle Punch to punch a hole in the top of the ovals.
Mount the "Eat at your own risk." sentiment on Block A. Ink it up with the Pumpkin Pie Ink Pad. Stamp it in the center of the scrap of Very Vanilla Cardstock.
Unlock the 1" Circle Punch. Holding the punch upside down so you can see the punching area, slide the stamped sentiment into the punch. Carefully line up the sentiment so it is centered in the punching area. Punch.
Use the brush tip of the Pumpkin Pie Marker to outline the edges of the sentiment circle.
Unlock the 1-1/4" Circle Punch. Slide the scrap of Lemon Lime Twist Cardstock into the punch. Punch.
Adhere the sentiment circle to the center of the Lemon Lime Twist circle using Stampin' Dimensionals.
Adhere the sentiment circles to the left side of the ovals just above the potion bottles. Let the left side of the circles stick over the left side of the ovals just a tiny bit. Be careful not to cover the hole punched in the top of the ovals.
Cut out a witch hat from a piece of Spooky Night Designer Series Paper using Paper Snips.
Use the Pumpkin Pie and Lemon Lime Twist Markers to color in parts of the witch hat as desired.
Adhere the witch hat to the upper right side of the ovals at a slight angle. Let the lower left side of the hat overlap the Lemon Lime Twist circle on the upper right just a bit and let the point of the hat stick off to the upper right of the ovals a bit. Be careful not to cover the hole punched in the top of the ovals.
Fill a Treat Tube with some treats and push the cork stopper firmly into place.
Cut a 5" piece of Vintage Crochet Trim.
Wrap the trim around the top of the Treat Tube and secure in place with a half knot.
Slide one end of the trim through the hole punched in the top of the oval tag from the back side. Secure the oval tag in place with a half knot. Trim the ends of the Vintage Crochet Trim.