F un card using Stampin' Up! products including a set that can be earned for FREE during Sale-A-Bration 2019!
Project Recipe
Cut cardstock and designer paper pieces to the following sizes using a Stampin' Trimmer:
- card from Lemon Lime Twist Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 4" x 5-1/4" from Shaded Spruce Cardstock
- 3-7/8" x 5-1/8" from Whisper White Cardstock
- 2" x 5" of small Lemon Lime Twist gingham pattern from Gingham Gala 6" x 6" Designer Series Paper
- 2-1/8" x 3-5/8" from Shaded Spruce Cardstock
- 2" x 3-1/2" from Whisper White Cardstock
- scraps of Lemon Lime Twist and Shaded Spruce Cardstock
Mount the sentiment of choice from the So Hoppy Together Set on Block A. Ink it up with the Shaded Spruce Ink Pad. Stamp it in the lower right corner of the large white rectangle.
Adhere the strip of Gingham Gala Designer Series Paper to the left side of the stamped white rectangle.
Adhere the stamped white rectangle to the large Shaded Spruce rectangle and then to the front of the Lemon Lime Twist card.
Mount the frog riding a unicycle image from the So Hoppy Together Set on Block I. Ink it up with the StazOn Ink Pad. Stamp it in the center of the smaller white rectangle.
Squeeze the lid of the Lemon Lime Twist Ink Pad to get a pool of ink in the lid. Open the pad but leave the lid exposed. Pick up some ink from the lid using the Blender Pen. Color in the body and legs of the frog and the pole of the unicycle. Get more ink on the Blender Pen as needed.
Tip: Stroke the Blender Pen in one direction only. If you go back and forth, then the cardstock could start to pill and tear. Scribble on Grid Paper to clean the tip of the Blender Pen until no more color is coming off.
Squeeze the lid of the Shaded Spruce Ink Pad to get a pool of ink in the lid. Open the pad but leave the lid exposed. Pick up some ink from the lid using the Blender Pen. Color in the belly of the frog and the seat, pedals, and belt of the unicycle. Get more ink on the Blender Pen as needed.
Tip: Stroke the Blender Pen in one direction only. If you go back and forth, then the cardstock could start to pill and tear. Scribble on Grid Paper to clean the tip of the Blender Pen until no more color is coming off.
Squeeze the lid of the Basic Gray Ink Pad to get a pool of ink in the lid. Open the pad but leave the lid exposed. Pick up some ink from the lid using the Blender Pen. Color in the gears and tire of the unicycle. Get more ink on the Blender Pen as needed.
Tip: Stroke the Blender Pen in one direction only. If you go back and forth, then the cardstock could start to pill and tear. Scribble on Grid Paper to clean the tip of the Blender Pen until no more color is coming off.
Adhere the colored frog on a unicycle image to the smaller Shaded Spruce rectangle and then to the front of the card so it is centered over the right edge of the designer paper and about 5/8" from the top.
Unlock the small punch that punches out a tiny circle and a small leaf shape from the Bitty Blooms Punch Pack. Punch out two small circles from a scrap of Shaded Spruce Cardstock and one small circle from a scrap of Lemon Lime Twist Cardstock.
Use a tiny dot of glue from the Fine-Tip Glue Pen or the Multipurpose Liquid Glue to adhere the circles to the card front so it appears the frog is juggling them.