Michele Reynolds
http://inspirationink.typepad.com/inspiration-ink/ michelerey@aol.com |
Game On Lucky Me Fun Fold |
F un fold card using Stampin' Up! products.
Cut cardstock and designer paper pieces to the following sizes using a Paper Trimmer:
- card from Pacific Point Cardstock at 4-1/4" x 7" and scored at one end at 1-1/2"
- 4" x 5-1/4" from Basic White Cardstock
- 1-1/2" x 4-1/4" from Pacific Point Cardstock
- 2 pieces each 1-1/4" x 4" of tiny blue flower diamonds with white centers on red plaid background design from Well Suited Designer Series Paper
- 2" x 4-1/4" from Pacific Point Cardstock
- 3-1/4" square from Poppy Parade Cardstock
- 3-1/4" square from Basic White Cardstock
- 1-3/4" x 2-3/4" from Basic White Cardstock
WITHOUT ADHERING, lay the large white rectangle on the inside back flap of the Pacific Point card. Lay the 1-1/2" x 4-1/4" strip across the bottom so it lines up with the bottom edges of the Pacific Point card.
Mount the dice image from the Game On Set on Block B. Ink it up with the Poppy Parade Ink Pad. Stamp it on the white layer just above the Pacific Point strip and as close to the right edge of the white layer as possible.
Now, adhere the stamped white layer in place to the inside back flap of the Pacific Point card.
Adhere one of the strips of Well Suite Designer Paper to the small front flap of the Pacific Point card. Adhere the other piece of designer paper to the 1-1/2" x 4-1/4" strip of Pacific Point.
Insert the 2" x 4-1/4" Pacific Point strip into the Dainty Diamonds 3D Embossing Folder. Make sure it is lined up straight. Place the folder with the cardstock inside on a platform on your Stampin' Cut & Emboss Machine and run through the machine.
Place the strip of Pacific Point with the designer paper attached along the bottom of the card so it lines up with the bottom and side edges.
Put strips of Tear & Tape Adhesive across the very top and very bottom of the vertical dry embossed Pacific Point strip. Remove the protective backings. Adhere the dry embossed Pacific Point strip to the top and bottom flaps of the Pacific Point card so it is about 5/8" from the left edge. This is the piece that holds the bottom of the card in place.
Pick out the stitched circle die from the Stitched Shapes Dies that cuts out a circle that is 3" diameter. Put it on top of the Poppy Parade square on a platform on your Stampin' Cut & Emboss Machine. Run through the machine.
Put strips of Stampin' Seal or Tear & Tape Adhesive vertically down the center of the back of the Poppy Parade circle cut out only. Adhere the circle cut out to the dry embossed Pacific Point strip on the front of the card so it is centered side to side and is about 1/4" from the top of the strip. Make sure NO adhesive goes past the edges of the Pacific Point strip or your card will be sealed shut.
Mount the hand of cards image from the Game On Set on Block E. Ink it up with the Poppy Parade Ink Pad. Stamp it in the center of the white square.
Pick out the stitched circle die from the Stitched Shapes Dies that cuts out a circle that is 2-1/2" diameter. Put it on top of the stamped cards image on a platform on your Stampin' Cut & Emboss Machine so the cards are centered in the circle as shown. Run through the machine.
Adhere the hand of cards circle cut out to the center of the Poppy Parade circle cut out.
Mount the "Lucky Me Because I Have You" sentiment from the Game On Set on Block G. Ink it up with the Poppy Parade Ink Pad. Stamp it in the center of the remaining white strip.
Pick out the stitched label die from the Stitched Nested Labels Dies that cuts out a label that is 1-1/4" x 2-1/4". Put it on top of the stamped sentiment on a platform on your Stampin' Cut & Emboss Machine so the sentiment is centered. Run through the machine.
Adhere the sentiment label cut out to the bottom of the dry embossed Pacific Point strip so it is centered side to side and is about 1/2" from the bottom of the strip. It will overlap the bottom of the hand of cards circle cut out a bit. Make sure NO adhesive goes over the edges of the dry embossed Pacific Point strip or your card will be sealed shut.
Use the mini spatula on the Take Your Pick to carefully peel up 3 red hearts from a sheet of Resin Hearts making sure that you get the adhesive backings as well. Adhere them to the bottom of the dry embossed Pacific Point strip so they are evenly spaced in a line.