Michele Reynolds
http://inspirationink.typepad.com/inspiration-ink/ michelerey@aol.com |
Follow Your Dreams Bag Tag |
P retty tag using Stampin' Up! products.
|
|
|
Cut cardstock and Multipurpose Adhesive Sheets to the following sizes for each tag using a Stampin' Trimmer:
- 2" x 5" from Powder Pink Cardstock
- 2" x 3-3/4" from Whisper White Cardstock
- 1-1/2" x 3-1/4" from Powder Pink Cardstock
- 1-3/8" x 3-1/8" from Mulitpurpose Adhesive Sheets
- 2" square from Silver Glimmer Paper
- 1" x 2-1/4" from Powder Pink
Unlock the Scalloped Tag Topper Punch. Slide one end the wide Powder Pink strip into the punch as far as it will go. Punch.
Mount the "follow your dreams" sentiment from the Follow Your Dreams Set on Block G. Ink it up with the Berry Burst Ink Pad. Stamp it on the bottom of the tag.
Mount the dream catcher image from the Follow Your Dreams Set on Block I. Ink it up with the Berry Burst Ink Pad. Stamp it in the center of the white rectangle.
Pick out the matching, open, dream catcher framelit from the Chase Your Dreams Framelits. Place the stamped dream catcher image on the Cutting Pad on top of the Magnetic Platform on the Big Shot. Place the dream catcher framelit on top so it is centered over the dream catcher image. Place another Cutting Pad on top and run through the Big Shot.
Pick out the detailed, circular thinlit from the Chase Your Dreams Framelits. Place it on top of the cut out dream catcher image on the Precision Base Plate on top of the Platform on the Big Shot so the circle thinlit is lined up over the circle on the top of the dream catcher. Place a Cutting Pad on top and run through the Big Shot a couple of times. Use the Die Brush to remove the pieces.
Carefully peel up the protective backing on one side of the Multipurpose Adhesive Sheet and adhere the adhesive sheet to one side of the medium Powder Pink rectangle. Leave the other protective backing piece in place.
Place the Powder Pink rectangle on the Precision Base Plate on top of the Platform on the Big Shot so that the adhesive side (with protective backing in place) is on the bottom (Powder Pink facing up).
Pick out the smaller, detailed dream catcher thinlit from the Chase Your Dreams Framelits. Place it on top of the Powder Pink rectangle on the Big Shot. Place a Cutting Pad on top and run through the Big Shot a couple of times. Use the Die Brush and Paper-Piercing Tool to remove the pieces.
Peel the protective backing off of the smaller dream catcher cut out and adhere it to the center of the larger dream catcher cut out.
Pick out the open circle framelit from the Chase Your Dreams Framelits. Place the square of Silver Glimmer Paper on the Cutting Pad on top of the Magnetic Platform on the Big Shot. Place the circle framelit on top. Place another Cutting Pad on top and run through the Big Shot.
Put a little bit of SNAIL on the back of the larger dream catcher cut out in the center of the filigree circle. Adhere the Glimmer Paper circle to the back of the larger dream catcher cut out so it is centered behind the filigree circle.
Use Stampin' Dimensionals to adhere the dream catcher to the center of the tag just above the sentiment.
Mount the stamp with the single and double feathers on it from the Follow Your Dreams Set on Block G. Ink it up with the Berry Burst Ink Pad. Stamp it in the center of the thin strip of Powder Pink Cardstock.
Pick out the matching framelit that cuts out the small feathers separately from the Chase Your Dreams Framelits. Place the stamped feathers on the Cutting Pad on top of the Magnetic Platform on the Big Shot. Place the small feathers framelit on top so it is centered over the feathers images. Place another Cutting Pad on top and run through the Big Shot.
Adhere the cut out double feathers to the top of the dream catcher so they appear to be coming from the center of the filigree circle and hanging down on the right side.
Adhere the single feather cut out so it tucks under the double feathers a bit.
Carefully peel up a circular rhinestone gem from the sheet of Petal Pink Rhinestone Gems making sure that you get the adhesive backing as well. Adhere it to the center of the filigree circle on the dream catcher.
Cut an 18" piece of Berry Burst 3/8" Metallic-Edge Ribbon. Fold it in half. Stick the folded end through the hole in the top of the tags from the front side. Pull it through a bit. Poke the open ends of the ribbon through the fold loop and pull tight.
Cut a 10" piece Whisper White Solid Baker's Twine and tie it to the ribbon right above the top of the tag using a small bow. Trim the ends.