Michele Reynolds
http://inspirationink.typepad.com/inspiration-ink/ michelerey@aol.com |
Custom Tee Red Birthday Girl Shirt |
R eal Red birthday card for a friend who loves red! Uses Stampin' Up! products from the Occasions Catalog.
|
|
|
Cut card stock and designer paper pieces to the following sizes using a Stampin' Trimmer:
- card from Real Red Card Stock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 4" x 5-1/4" from Whisper White Card Stock
- 3-7/8" x 5-1/8" from Real Red Card Stock
- 2-1/4" square of tiny white hearts on red design of paper from Sending Love Designer Series Paper Stack
- scrap of dotted lines and hearts in red on white design of Sending Love Designer Series Paper Stack at least 3/4" x 2-3/4"
- scrap of Whisper White Card Stock at least 3/4" x 1-1/4"
Place the Real Red rectangle into the Falling Petals Textured Impressions Embossing Folder so that the hearts/petals are concentrated at the bottom edge of the card stock. Place the folder with the card stock inside on top of a Cutting Pad on your Big Shot Platform at the lowest possible setting. Place another Cutting Pad on top of the folder and run through the Big Shot. Make sure none of the edges are hanging off the platform or they could snag.
Adhere the embossed red rectangle to the white rectangle and then to the front of the Real Red card.
Mount the woman's t-shirt image from the Custom Tee Photopolymer Set on Block C. Ink it up with the Basic Black Archival Ink Pad. Stamp it on the square of red with white hearts designer paper so the hearts are oriented properly.
Pick out the women's t-shirt framelit from the T-Shirt Builder Framelits. Place the designer paper square with the stamped t-shirt on the Cutting Pad on top of the Magnetic Platform on your Big Shot. Place the t-shirt framelit over the stamped t-shirt image. Place the other Cutting Pad on top and run through the Big Shot.
Mount the lace collar image from the Custom Tee Photopolymer Set on Block A. Ink it up with the Real Red Ink Pad. Stamp it on the small scrap of Whisper White Card Stock.
Pick out the rounded collar framelit from the T-Shirt Builder Framelits. Place the card stock with the stamped collar on the Cutting Pad on top of the Magnetic Platform on your Big Shot. Place the rounded collar framelit over the stamped collar image. Place the other Cutting Pad on top and run through the Big Shot.
Use a small amount of Multipurpose Liquid Glue and adhere the collar to the top of the t-shirt.
Mount the long skinny sash outline image from the Custom Tee Photopolymer Set on Block G. Ink it up with the Real Red Ink Pad. Stamp it on the scrap of white with dotted lines and hearts designer paper.
Mount one of the long skinny sentiments from the Custom Tee Photopolymer Set on Block G. Ink it up with the Real Red Ink Pad. Stamp it on the scrap of white with dotted lines and hearts designer paper so it is within the lines of the stamped sash.
Pick out the sash framelit from the T-Shirt Builder Framelits. Place the designer paper with the stamped sash on the Cutting Pad on top of the Magnetic Platform on your Big Shot. Place the sash framelit over the stamped sash image. Place the other Cutting Pad on top and run through the Big Shot.
Adhere the sash across the t-shirt.
Adhere the t-shirt to the center of a Lace Doily with the white side of the doily facing up.
Put more adhesive on the back of the doily where it is hidden by the t-shirt. Adhere the doily to the right side of the card front.
Cut a 3-1/2" piece of the silver 3/8" Metallic Ribbon Combo Pack ribbon. Tie a half knot in the ribbon. Attach it to the bottom left corner of the t-shirt with a Mini Glue Dot.