S parkly Halloween card using Stampin' Up! products.
Project Recipe
Cut cardstock, designer paper, glitter paper, and Foam Adhesive Sheets pieces to the following sizes using a Paper Trimmer:
- card from Highland Heather Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 4" x 5-1/4" of tiny, multi-colored dots on white background design from Cute Halloween 6" x 6" Designer Series Paper
- 1-1/4" x 3-1/4" from Black 12" x 12" Glitter Paper
- 1-1/8" x 3-1/8" from Foam Adhesive Sheets
- - 1-1/4" x 3-1/2" from Basic White Cardstock
- large circle cut from tiny white "boo!" words all over black background design from Cute Halloween 6" x 6" Designer Series Paper using the Picture This Dies
As you are ready to stamp using the Cutest Halloween Set, place the cardstock or designer paper on the Stampin' Pierce Mat. Using the mat will help you get a cleaner image each time you stamp.
Mount the "hey, boo!" sentiment from the Cutest Halloween Set on Block G. Carefully press the stamp to the edge of the open Jet Black StazOn Ink Pad or Tuxedo Black Memento Ink Pad so you ink up ONLY the word "boo!". Stamp the word in the upper right corner of the horizontal, dotted designer paper rectangle.
Adhere the stamped designer paper rectangle to the front of the Highland Heather card.
Adhere the circle of "boo!" words designer paper to the left side of the card front so it is about 3/4" from the bottom and about 5/8" from the left side.
Tip: Use a circle cut out from a previous project.
Peel the protective backing off of the Foam Adhesive Sheets rectangle. Adhere the Adhesive Sheets rectangle to the back (non-glittery) side of the Black Glitter Paper rectangle. Be sure to leave the other protective backing in place for now.
Pick out the word "Halloween" die from the Word Wishes Dies. Put it on top of the Black Glitter Paper rectangle with Foam Adhesive Sheet on back on a platform on your Stampin' Cut & Emboss Machine so the glittery black side is face up. Run through the machine. Use the Take Your Pick Die Brush Tip and paper-piercing tool on the Take Your Pick to remove the pieces. Leave the protective backing in place for now.
Peel the protective backing off the "Halloween" word cut out and adhere it to the front of the card so it overlaps the bottom right side of the "boo!" word circle just a tiny bit.
Mount the outline ghost image from the Cutest Halloween Set on Block B. Ink it up with the Jet Black StazOn Ink Pad or Tuxedo Black Memento Ink Pad. Stamp it on the bottom edge of the long, skinny white strip.
Mount the solid ghost image from the Cutest Halloween Set on Block B. Ink it up with the Highland Heather Ink Pad. Stamp it inside the ghost outline image.
Mount the ghost face and arms image from the Cutest Halloween Set on Block A. Ink it up with the Jet Black StazOn Ink Pad or Tuxedo Black Memento Ink Pad. Stamp it inside the ghost image.
Unlock the Halloween Punch. Holding the punch upside down so you can see the punching area, slide the stamped ghost outline image into the punch and get it centered in the corresponding punching area. Punch.
Adhere the ghost punch out to the front of the card so it overlaps the upper right side of the "boo!" words circle cut out just a bit.
Cut a 3-1/2" piece of the Black 3/8" Glittered Organdy Ribbon.
Tie a half knot in the center of the ribbon. Trim the ends.
Use a Mini Glue Dot to adhere the ribbon knot to the front of the card at the base of the "H" in the word "Halloween" on the left side.
Use the mini spatula on the Take Your Pick to carefully peel up three different sizes and colors of stars from the sheet of Cute Stars Adhesive-Backed Sequins making sure that you get the adhesive backings as well. Adhere them randomly around the stamped "boo!" word in the upper right corner.