F un treat holders perfect for fall festivities made with Stampin' Up! products.
Project Recipe
Cut card stock and designer series paper pieces to the following sizes using a Stampin' Trimmer:
- 2 pieces, each 3-3/4" x 5-1/2" cut from matching patterns of Wood Textures Designer Series Paper Stack, cut so the grain of the wood is horizontal across the 5-1/2" direction
- 2-1/4" square from Tangerine Tango Cardstock
- 2-1/4" square from Gold Foil Sheets
- scrap of Very Vanilla Cardstock at least 1-1/2" wide
- scrap of Early Espresso Cardstock at least 1-1/2" wide
- scrap of vanilla dots on peach watercolor wash background design from Painted Autumn Designer Series Paper
- set of three pumpkins cut from pumpkins on vanilla background design from Painted Autumn Designer Series Paper
Pick out the half crate framelit from the Wood Crate Framelits. Place one piece of the Wood Textures Designer Paper on the Cutting Pad on top of the Platform on the Big Shot. Place the half crate framelit on top. Place another Cutting Pad on top and run through the Big Shot. Repeat with the other piece of designer paper.
Fold the crate pieces on all score lines. Use Tear & Tape Adhesive on the flaps to adhere the two crate pieces together. Use SNAIL on the bottom flaps to hold them together. Be aware that the short sides of the crate stick up above the front and back sides of the crate.
Pick out the detailed leaf thinlit from the Seasonal Layers Thinlits. Place the Gold Foil Sheets square on the Precision Plate on top of the Platform on the Big Shot. Place the detailed leaf thinlit on top. Place a Cutting Pad on top and run through the Big Shot a couple of times. Use the Die Brush to remove the cardstock.
Pick out the open large leaf framelit from the Seasonal Layers Thinlits. Place the Tangerine Tango cardstock on the Cutting Pad on top of the Magnetic Platform on the Big Shot. Place the leaf framelit on top. Place another Cutting Pad on top and run through the Big Shot.
Place the detailed leaf cut out upside down on one side of a Silicone Craft Sheet. Cut a Stamping Sponge into quarters and clamp the triangle edge of one quarter in a large binder clip. Squeeze a small amount of Multipurpose Liquid Glue on one corner of the Silicone Craft Sheet. Dab the sponge into the glue and then lightly onto the back of the detailed leaf cut out. Flip the detailed leaf cut out over and adhere it to the Tangerine Tango leaf.
Put a small piece of Tear & Tape Adhesive on the upper bar on the front right side of the crate. Remove the protective backing and adhere the leaf cut out to the front of the crate at an angle so the points of the leaf stick out a bit on top and on the right side.
If you haven't already done so, cut a group of 3 pumpkins out of the piece of Painted Autumn Designer Series Paper with Paper Snips.
Put a small piece of Tear & Tape Adhesive across the center bar on the front of the crate so it overlaps the left side of the leaf a bit. Remove the protective backing and adhere the pumpkins cut out to the front of the crate so it is centered side to side and the bottom of the white pumpkin is even with the bottom of the crate.
Unlock the 1" Circle Punch. Insert the Early Espresso Cardstock and punch.
Mount the "grateful" sentiment from the At Home with You Set on Block A. Ink it up with the Soft Suede Ink Pad. Stamp in the center of the scrap of Very Vanilla Cardstock.
Unlock the 3/4" Punch. Holding the punch upside down so you can see the punching area, slide the stamped sentiment into the punch. Carefully line up the sentiment so it is centered in the punching area. Punch.
Adhere the sentiment circle to the center of the Early Espresso circle using SNAIL.
Put a tiny piece of Tear & Tape Adhesive on the middle bar of the crate front so it overlaps the pumpkins on the left side just a bit. Remove the protective backing and adhere the matted sentiment circles.
Pick out the open small leaf framelit from the Seasonal Layers Thinlits. Place the scrap of vanilla dotted peach Painted Autumn Designer Series Paper on the Cutting Pad on top of the Magnetic Platform on the Big Shot. Place the leaf framelit on top. Place another Cutting Pad on top and run through the Big Shot.
Use a Stampin' Dimensional to adhere the small leaf cut out to the front of the crate so it overlaps the top of the sentiment circle with the stem going off to the right.
Cut a 3" piece of Gold 1/4" Natural Trim.
Tie the trim in a half knot. Trim the ends. Adhere the trim knot to the front of the crate using a Mini Glue Dot so it is at the bottom right of the sentiment circles.