A dorable card using Stampin' Up! products including some that can be earned for FREE during Sale-A-Bration 2023.
Project Recipe
Cut cardstock and designer paper pieces to the following sizes using a Paper Trimmer:
- card from Cherry Cobbler Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 4" x 5-1/4" from Basic White Cardstock
- 2-1/4" x 4" of red plaid design from Day At The Farm 12" x 12" Designer Series Paper
- 3" square from Crumb Cake Cardstock
- 1-1/2" x 2-3/4" from Basic White Cardstock
- scrap of red plaid design from Day At The Farm 12" x 12" Designer Series Paper
Insert the large Basic White rectangle into the dotted embossing folder from the Basic 3D Embossing Folders. Use the line printed on the front flap of the folder to make sure it is lined up straight. Place the folder with the cardstock inside on the platform on your Stampin' Cut & Emboss Machine and run through the machine.
Adhere the large piece of plaid Day At The Farm Designer Paper to the bottom of the dry embossed vertical white cardstock.
Cut a 10" piece of the Crumb Cake twine from the Baker's Twine Essentials Pack.
Fold the twine in half. Lay the folded twine across the white/designer paper rectangle so it covers the seam between the two pieces. Fold the ends of the folded twine over and secure the ends of the folded twine in place with strips of Tear & Tape Adhesive.
Remove the protective backings from the Tear & Tape strips and add Stampin' Seal to the back of the white rectangle. Adhere it to the front of the Cherry Cobbler card.
Mount the owl with bowtie image from the Adorable Owls Set on Block C. Ink it up with the Tuxedo Black Memento Ink Pad. Stamp it in the center of the Crumb Cake square. Leave the stamp on the block.
Pick out the stitched circle die from the Stylish Shapes Dies that cuts out a circle that is 2-9/16" in diameter. Put it on top of the stamped owl square on a platform on your Stampin' Cut & Emboss Machine so it is centered over the owl side to side with the owl slightly closer to the top edge. Run through the machine.
Adhere the owl circle cut out to the front of the card so it is centered side to side and is about 5/8" from the top of the card.
Mount the sentiment of choice from the Adorable Owls Set on Block G. Ink it up with the Cherry Cobbler Ink Pad. Stamp it in the center of the white strip.
Pick out the double-notched label die from the Stylish Shapes Dies that cuts out a label that is 7/8" x 2-1/4". Put it on top of the stamped sentiment on a platform on your Stampin' Cut & Emboss Machine so it is centered over the sentiment. Run through the machine.
Use Stampin' Dimensionals to adhere the sentiment label cut out to the front of the card so it is centered side to side over the twine and overlaps the bottom of the owl circle cut out a bit.
Re-ink the owl with bowtie image on Block C with the Tuxedo Black Memento Ink Pad. Stamp it on the scrap of red plaid Day At The Farm Designer Paper so you get the bowtie.
Use Paper Snips Scissors to cut out the bowtie stamped on the designer paper scrap by hand.
Use Multipurpose Liquid Glue or Fine-Tip Glue Pen to adhere the cut out designer paper bowtie over the top of the bowtie on the stamped owl circle cut out.
Cut an 8" piece of the Crumb Cake twine from the Baker's Twine Essentials Pack.
Fold the twine in half. Slide the folded end of the twine under the twine already on the card front on the left side of the sentiment label cut out. Tie in place with a half knot. Trim the ends.